Energy Losses in Pipes

Energy Losses in Pipes ABSTRACT The objective of this lab is to associate the loss of energy in a hydraulic system with the geometry of the pipe, that contains the fluid, while it is being transported from one location to another. Special considerations were given to major and minor energy losses. Friction was taken and treated as a major loss with respect to energy, while other factors such as expansions, contractions, pipe bends, pipe fittings and obstructions were considered as minor energy losses. The design of any hydraulic systems is governed by the understanding of these relations, and this experiment is carried out with the intention proving that there is a loss of energy specifically related to these factors. [4] The DMXL Base Unit  ® in accordance with the DLM-6  ® cartridge were used to perform the experiment, using water as the medium of choice. The cartridges pressure transducers recorded the pressure differences at three locations of interest. The locations included a straight pipe secti on, a smooth 90 ° bend, and a sharp 90 ° right angle turn. For proper comparison, these results were all at the same length, of 70 mm. A total of 20 data points were tabulated, and used to calculate the loss of energy coefficients and head loss, for of all three sections. The results showed that there was a greater loss of energy with the sharp 90 ° right angle, followed by the smooth 90 ° bend and finally, the straight section had the least amount of energy loss. According to the principles of fluid mechanics, the assumption is that the highest loss of energy would correspond to the sharp 90 ° right angle bend. The results reinforced that assumption. INTRODUCTION In almost all hydraulic systems, it can be observed that there are energy losses with respect to friction and geometrical changes. The friction loss in pipes is due to the influence of the fluids viscosity near the surface of the surrounding pipe. The energy losses due to pressure changes can be seen in every part of a hydraulic system due to the expansions, contractions, bends in pipes, pipe fittings, and obstructions in the pipes. [2] This loss of energy is then transferred as heat. Frictional losses in pipework are related to: Velocity of flow Roughness of pipe surface Length of pipe Cross-sectional area of pipe Viscosity of fluid Number of pipe bends The complete acceptable pressure drop of the hydraulic system must be picked with care, as the power loss is a result of the pressure drop and system flow rate. There is an efficiency loss that must be adjusted for the cost of bigger fittings and hoses and pipework. The energy of no use is disseminated as heat energy in oil, which may prompt to cooling issues and condensing of the oil life. [1] Pressure losses in pipework will rely on the fluid flow condition. There are three particular fluid flow conditions: Laminar Flow Turbulent Flow Transition Flow As it can be seen in Figure 1, Laminar stream is the condition when the liquid particles travel easily in straight lines, the internal most liquid layer goes at the most elevated speed and the external most layer at the pipe surface doesnt move. [2] Figure 1. Laminar Flow [2] Turbulent flow has unusual and disorderly liquid molecule movements, to such an extent that a comprehensive blending of the fluid happens, as appeared in Figure 2. A turbulent flow is generally not attractive, as the flow resistance increments and in this way the hydraulic losses increment. [3] Figure 2. Turbulent Flow [3] As shown in Figure 3, with turbulence in the focal point of the pipe, and laminar flow close to the edges, the transactional flow can be seen that it is a blend of the turbulent and laminar flow. [2] Figure 3. Transitional Flow [2] Inside a pipe system, there are two sorts of losses. The first is a Major Loss and comprises of the head losses because of viscous impacts in straight fragments of pipe in the system. [5] Which is referred to as h_(L major) and the equation follows as: (1) The second sort is a Minor Loss and is a form of losses produced inside segments of the pipe system other than the straight pipes themselves. [5] Which is referred to as h_ (L minor) and the equation follows as: (2) The equation for head loss at a sudden expansion can be written as: (3) And expression for the head loss at a sudden contraction is as: (4) The head loss due to a bend can be shown by the expression as: (5) METHODOLOGY Equipment and Materials List: For the experiment, we used the Energy Losses in Hydraulic Systems cartridge on DLMX Base Unit  ®. The DLMX is a teaching equipment that can be presented as one of the absolute best designed educating device that is utilized to teach students from various different subjects like Fluid Mechanics and Heat Transfer. The equipment includes a small battery operated, base unit, into which has one of the seven different cartridges is plugged. [3] The base unit contains: Viewing panel Water reservoir Pump Controls Experimental Apparatus: According to the General Operating Instructions from the provided lab manual, the DLM-6 cartridge (Energy Losses in Hydraulic Systems)  ® was installed as shown below in Figure 4, with a filled Base Unit and powered on. The flow rate was adjusted using the knob on the Base Unit. The flow rate and corresponding differential pressure readings across the straight pipe, smooth bend and sharp bend sections appeared on the output screen. Figure 4. DLM-6 cartridge (Energy Losses in Hydraulic Systems) [3] The cartridges have the particular instrumentation required for the specific demonstration and contain an experimental representation of the topic. The base unit involves a round, clear acrylic water reservoir, mounted on a powerful vacuum shaped ABS plastic plinth, shown below in Figure (#). Under the plinth is a pump with a variable speed control, battery, flow meter, the electrical control hardware, and level sensor [6]. Figure (5) Energy Losses in Hydraulic Systems cartridge on DLMX Base Unit [3] Experimental Procedure: To commensurate our lab, we referred to Filling Pressure Transducer Tubes section as we powered on the machine. We then installed the DLM-6 cartridge (Energy Losses in Hydraulic Systems)  ® into the Base Unit filled with water and ensured that all pressure readings are at zero flow rate. We can read the flow rate and pressure drop at that moment is given if we scrolled down on the display on the machine. Next, we checked for the possible maximum flow rate. From there we were able to get an estimate of the increment differences needed for each reading. The flow rate was set to ~ 1 L/min and increased in approximately equal increments until the maximum flow rate was achieved. And then the pressure drop was obtained and recorded. Steps were repeated until Experimental DLMX  ® data table is completed. RESULTS Table 1 shows the data points recorded from different runs of fluid flowing through ΆP Straight, ΆP Smooth, and ΆP RA Bend. Table 1. Data points recorded from the experiment. Dimension Constants: Square pipe width = 4 mm Smooth bend radius = 8 mm (to channel center) Distance between pressure taps: Straight section: 70 mm Smooth bend section: 70 mm Sharp bend section: 70 Ç‚RA = right angle bend Velocity: In Table 2, we found the Velocity by using the equation of Flow rate, Area: (area = 0.004*0.004 =0.000016 m2); Q: Flow rate (6) Table 2. Velocity obtained from different runs. Headloss: Head loss for straight, smooth and right angle pipe are shown below in Table 3: We used Pascals Law to calculate the loss coefficient. This can be found by using equation of: HL = (7) Table 3. Head loss for straight, smooth and right angle pipe Loss Coefficient: K smooth =289.30, k RA= 267.48, f Straight= 1.461*10^-4, As we know that hydraulic diameter, (8) (9) therefore, The values below are derived from basic equation of Head loss, HL = {This same equation is used for straight pipes} {This same equation is used for smooth and RA pipes} In the above equations f and K are the loss coefficients. Loss coefficients for straight, smooth and right angle pipes are shown below: Table 4. Loss coefficients of Straight, Smooth, and RA Bend Pipe. DISCUSSION In order to obtain the pressure difference in a circular pipe it is possible to reduce the energy equation as follows. (10) (11) Where, à ¡Ã¢â‚¬ËœÃ‚ ­ = Density of fluid, g = gravity, h = height, P = pressure, V = average velocity, z = elevation and This reduction is applicable when the cross-sectional area as well as the elevation are equal. For circular channels, the head loss due to flow can be obtained using the equation below. (12) Where, f = Stanton friction factor, L = length of circular channel, D = diameter, V = average velocity and g = gravity. In contrast to circular channels, the energy equation can also be used to obtain the pressure difference in noncircular channels as follows. (13) However, in noncircular channels, the head loss due to flow can be obtained using the equation (14) Where, (15) Moreover, the friction factor for non-circular channels is a function of the roughness factor divided by the hydraulic radius and the Reynolds number. (16) For noncircular channels, the Reynolds number is also calculated using the hydraulic diameter as follows. (17) It is possible to measure pressure losses arising from fittings to the piping system using the DLMX fluid mechanics cartridge fitted with differential pressure transducers that connected to pressure taps which registers the difference in pressure related to the flow. The pressure difference can be evaluated using the energy equation that includes major friction losses due to fittings on the piping system as follows. (18) For the cartridge, the energy balance equation begins as follows below. (19) Considering the cartridge as a closed system the energy balance equation reduces as follows below. (20) Physically, represents the pressure losses per unit mass of water in the cartridge. On the other hand, represents the differences in pressure at the three points of interest associated with flow. The hierarchy of pressure difference starting from the least pressure difference to the highest is as follows below. The pressure drop at the right-angled bend can be calculated using from the energy balance equation below. (21) Because there is no change in diameter throughout the length of the bend, no change in elevation, as well as no change in elevation, the energy balance equation reduces to. (22) The loss coefficient is a dimensionless coefficient derived from dividing the head loss by as follows below. (23) Therefore, Finally, to calculate the required pressure losses in the bend the equation above reduces as follows below. (24) At the straight portion of the pipe, the pressure drop equation reduces as follows below. (25) Where f=the friction coefficient, D=diameter of the pipe and L= the length of the pipe. In order to find the length of straight pipe that would be sufficient to generate the same amount of pressure drop at the right-angled bend the pressure drops have to be made equal as follows below. (26) The length of the pipe then reduces to the formula below. (27) It is possible to determine the loss coefficient graphically from the experimental values by creating a graph of the head loss vs dynamic head. (28) Where and = dynamic head, the loss coefficient Figure 6. Head loss vs Dynamic Head CONCLUSION The goals of this lab was to measure the head losses through straight, smooth, and sharp- bend pipe fittings and then use these measurements to estimate the loss of energy coefficients for each transition or fitting. For the experiment, the DML-6  ® cartridge (Energy Losses in Hydraulic Systems) was used with the DLMX Base Unit  ®, using water as the fluid of choice. The flow rate and corresponding differential pressure readings across the straight pipe, smooth bend and sharp bend sections were all recorded. A total of 20 data points were collected. The collected datas were used to calculate the head losses and loss of energy coefficients for all three sections. The results show that the pressure difference in the right-angle bend is higher than smooth bend, and pressure difference in smooth is higher than the straight bend pipes. Also, the average head loss of a right-angle pipe, 1.633, is certainly higher than average head loss of the smooth, 2.144, and straight, 1.63 3. Furthermore, the average loss coefficient of right angle pipe, 16.84078, was also higher than smooth, 10.988725, and straight, 0.13513, pipes. Uncertainty analysis indicate that one possible source of error came from the pressure readings. The pressure readings at the reference point for each component and each flow was some value greater than zero, but the problem with this was that all the reference point readings should have been zero regardless of the set up. The reason for this difference is still unknown, however the doubt is that there was a problem with the machines manometer. The lesson learned with this experiment was the energy losses in pipes due to different fittings. The experiment was quite interesting, yet this hands-on approach lesson will help us succeed in the real engineering world as well. REFERENCES [1] Bruce Roy, Munson, T. H. Okiishi and Donald F. Young. Fundamentals of Fluid Mechanics. Hoboken, NJ: J. Wiley Sons, 2009. [2] Smith, W.F., Turbulent and Laminar Flow in Pipes, with the Particular Reference to the Transition between the Straight, Smooth and Rough Pipe Laws, J. Inst. Civ. Eng. Lond., vol.11, pp. 148-178, 1979-78. [3] DLMX Base Unit and DLM-6 Energy Losses in Hydraulic Systems. (2017, February 28). Retrieved from http://discoverarmfield.com/en/products/view/dlmx/desktop-learning-modules [3] Hibbeler, R. C. 10.2 Losses Occurring from Pipe Fittings and Laminar, Turbulent, and Transitions. Fluid Mechanics. N.p.: Pearson Prentice Hall, 2015. 578-46. Print. [4] Fluid Flow through between Pipes. Pump-House, University of South Carolina, Columbia (2007): n. pag. Web. http://www.cs.cdu.edu.au/home-page/jayitroy/eng477/sect10.pdf pg. 47 [5] Head Loss Coefficients of Major and Minor. Vano Engineering. N.p., 13 Dec. 2014. Web. 20 Jan. 2015. [6] Shukla. S.K., Indian Journal of Applied Research, of various different flow rates, vol. 7, no. 7, pp. 313-377, April. 2015. [7] Donald, James C., M. F. Sherif, and V. P. Kumar. 8.4 Minor and Major Losses in Pipes. Elementary Hydraulics. Mason, OH: Cengage Learning, 2004. 257-78. Print. [8] John Ray, W.F., 1947, Turbulent Flow in Pipes with Particular reference to the Transition Region between the Smooth and Rough Pipe Laws, J. Institution. of Civil Engr Dept., I7, pp 178-167. APPENDIX A We learned how different pipe fittings results in energy losses in pipes. Although it was quite difficult to do all the calculations, plus the presence of uncertainty created a doubt on the result, our team found this lab very interesting. The results were also close to the expected outcome. APPENDIX B Names Tasks Hours Rigoberto Aguilera Maaz Khan Esther Ndichu Trang Pham Prabhjit Singh APPENDIX C It should be noted that when using Bernoullis equation, one must take into consideration the height of a pipe. The data that was used in the calculations was processed without that consideration. The manufacturer of the unit explains that the pressure transducers inside the DLM-6  ® cartridge do not measure hydrostatic pressures between the taps, when the tubes are filled with water. As it can be seen in the image below the device is filled with water, but the water is not in motion. The levels of the manometer tubes are the same, regardless of the vertical setup. With the same concept in mind, it is clear to see that the pressure transducers will also fail to measure any pressure change with respect to gravity.

Total Quality Management (TQM) :: GCSE Business Marketing Coursework

Total Quality Management Total Quality Management is a structured system for satisfying internal and external customers and suppliers by integrating the business environment, continuous improvement, and breakthroughs with development, improvement, and maintenance cycles while changing organizational culture. A remarkable thing is happening as we see the awakening of the individual and the collaboration of empowered people in the team effort of total quality management. It is a renewing, a reinforcing and a building of a bridge of trust among the individuals responsible for accomplishing a common goal (The Total Quality Review; May 1994). One of the goals is to build an organizational environment conducive to job redesign and cross training in order to facilitate job flexibility. TQM initiatives in areas of common concern provide an opportunity to form and better control the relationship with a company's external vital customers and suppliers. TQM is essential for companies seeking to provide quality goods and services to their customers. The end result is that they will enjoy prosperity and long-term growth. "In order to compete in a global economy, our products, systems and services must be of a higher quality than our competition. Increasing Total Quality is our number on priority here at Hewlett-Packard. -John Young, President of Hewlett-Packard" (www.dmu.ac.uk.htm). Often companies find themselves faced with a dilemma that is rooted to a lack of TQM. This was the case with Apple Computers. They were unable to conceive a working, productive relationship between their managers and engineers. Apple found themselves unable to alleviate this problem, which ultimately hindered it from responding to environmental changes. The positive effects of TQM has transcended down through the ranks. Non-profit organizations have begun to embrace TQM throughout their organization, relying on the positive results found throughout the business world. Even the Health care industry has initiated TQM to promote excellence in nursing, urging nurses to apply quality improvement.

Analyzation of a quote from Things Fall Apart by Chinua Achebe Essay

In Things Fall Apart, Achebe focuses on differences in culture and society. In the quote, â€Å"The world has no end, and what is good among one people is an abomination with others.† Uchendu is discussing with Okonkwo and Obierka the massacre in Abame. I agree with the quotation. Many people have their own ways of doing things and then their actions are criticized by others. A prime example of this is religious groups in the world and all are criticized by one another at some point. A good example of that fueding is the on-going criticisms between Protestants and Catholics. Being Catholic myself, I can relate to this first-hand. Our beliefs to other religious groups are wrong, an abomination of what is â€Å"supposed to be done.† We also sometimes criticize our brethren in other faiths. The world is always in a constant fight. There is a deeper meaning in this quote and that meaning is that internally, the world will never end its constant criticism and bludgeoning of itself. It keeps going around in circles, and until one group decides to understand the other, the cycle will continue. Basically, the beliefs misunderstood by stubborn people who do not want to understand are picked on. The people whose beliefs are in question get angry and these differences are set in motion. And truly, until we all understand each other, universally, this cycle of craziness will certainly never end, making Uchendu’s statement correct.

The Backbone Of The Airline Industry - 754 Words

The backbone of the airline industry is the men and women that operate the aircraft for the world’s airlines. The nation’s airline pilots are some of the most skilled technical workers in the workforce. The skillset of a commercial pilot does not come cheap with the average commercial captain making over $165,000 per year (Time, 2016). The employment cost of running an airline has never been more, paving the way for unmanned aircraft to take over. Labor Costs Labor cost is the number one expense for operating an airline. According to airline.org, over 32% of an airline’s operating expense can be related to labor costs (A4A Quarterly Passenger Airline Cost Index: U.S. Passenger Airlines, 2016). Labor cost is a complex issue as it relates to commercial airlines. Flight crewmembers are limited under the Federal Aviation Regulations (FAR) to strict limitations on work and duty rules. An example of FAR’s that limit the efficiency of airline pilots are eight in a duty period and 30 in 7 Federal Aviation Regulations. Flight crewmembers are limited to eight hours of flight time between rest periods. The time between a rest periods is considered a duty period and crewmembers are unable to operate an aircraft greater than eight hours in a duty period. Additionally, flight crewmembers cannot exceed thirty flight hours in a rolling consecutive seven day period. The above mentioned rules reduce the efficiency of labor moving aircraft resulting in the need to hire moreShow MoreRelatedSouthwest Airlines And The Airline Industry946 Words   |  4 PagesExecutive Summary Southwest Airlines is a competitor in the airline industry who models themselves as a low fare company who cares about people. These two aspects are that backbone to their business. It is what sets them apart from their major competitors, such as Delta/Northwest, Continental/United, JetBlue, and Allegiant. Government regulation has allowed for more travel due to deregulation. This means there are more consumers than ever entering the industry. As more consumers enter the marketRead MoreOrganizational Competitive Strategies-Porters Five Forces Model (AIR ASIA)763 Words   |  4 Pages in this assignment, can be used to access the competitiveness of the airlines industry. It can review the competition within the industry plus checks for threat from outside. Bargaining power of supplier-High- In every industry, there has to be someone to play the role of a supplier. It is important to know the power of the supplier as it will affect the industry. There are only two main suppliers in the airline industry, Airbus and Boeing, thus there isn’t much of an open option. Not forgettingRead MoreOutsourcing In The Airline Industry833 Words   |  4 Pagesmanufactures like Boeing and Airbus to airlines outsourcing their maintenance, ground labor, even ticketing and customer service. Usually most proponents of outsourcing will cite that it saves money and possibly increases knowledge sharing, which can lead to new innovations. Those that are against outsourcing often bring up the fact that you can easily loose quality control, poor customer service and possible jeopardize safety in the pursuit of saving money. On the airline level outsourcing has taken overRead MoreSouthwest Airlines and Its Business Strategy 1097 Words   |  5 Pagesï » ¿Corporate Strategy Southwest Airlines faced many barriers to entry from the fierce competition of other airlines in the industry. Though competition was fierce, Southwest Airlines managed to succeed by doing things differently. Their mission was to provide affordable air travel to those who would not normally fly. Contradictory to the rest of the airline industry, Southwest maintained a profit while keeping its fares low. Southwest was unique to the industry in two ways. They focused on the shortRead MoreFinancial Issues Faced By Delta Airlines1358 Words   |  6 Pagesissues faced by a creative, innovative, and a well-established airline, Delta Airlines Company, which had successfully earned a reputable name in the airline industry with all its significant efforts. The company started its operations in the year 1928 and with the help of strong and effective leadership, the company successfully gained access to new routes, which ultimately resulted in the increased revenues for the company. The indust ry is filled with the number of competitors including the low costRead MoreBoeing Versus Boeing : Clash Of Industry Giants1113 Words   |  5 PagesBoeing versus Airbus: Clash of Industry Giants The applied science of flight can trace it roots back to the Montgolfier balloon in 1783. The birth of aviation, a lighter – than – air balloon, took the European continent by storm. France, Germany and the English had had their own experimental variations in this new methodology of travel. Each experiment slightly different, experiments in controlling flight through paddles, fabrics, heating sources. This eventually evolved into delivery of mailRead MoreAnalysis Of Coca Cola And America Airlines1374 Words   |  6 PagesFortune is an American organization that is responsible for the ranking of World’s biggest Companies in terms of annual income return and the profits that companies acquire at the end of every financial year. Coca cola and America Airlines are featured in Fortune 500 as World performing companies though American seem to unsuccessful compared with Coca cola which is selling in the global market and its market trend growing daily following its use of the modern supply chain for a classic beverage.Read MoreSouthwest Airlines: Using Human Resources for Competitive Advantage1445 Words   |  6 Pages Southwest Airlines: Using Human Resources for Competitive Advantage Executive Summary Southwest was founded in 1971 with a fleet of three Boeing 737 aircraft. Headquartered at Love Field in Dallas, the airline followed a strategy of low fares, few frills, and excellent customer service. Early on, the airline faced many political and regulatory challenges including the Wright Amendment, which prohibited the carrier from offering direct service into Love Field from any state other than TexasRead MoreSpecial Organization Features in Companies and Their Effectiveness1225 Words   |  5 Pagesorganizational culture features suitable to the organization and its people that ensure a win-win situation for the organization, its people and valuable customers. Southwest was established in 1967 by Rolling King and Herb Kelleher as an intrastate airline. It is now the fourth largest major airliner in USA and is trading on the New York Stock Exchange. The organization religiously reminded themselves that airplanes dont make money on the ground. Flights have to be maximised with the least numberRead MoreTourism Strategy of Nepal936 Words   |  4 Pagesinternational airport at Bara district and upgrading of few domestic airports (Adhikari, n.d.). In order to develop tourism throughout the country, The Ministry of Tourism and Civil aviation produced â€Å"Tourism Vision 2020† in consultation with its industry partners (Tourism Vision 2020, 2009). This booklet was published in May 2009. Visit Nepal 2011 was targeted to increase visitors mainly from India and China due to the growing economy power of the 2 countries as well as being 2 of the worlds most